Register    Login    Forum    Search    FAQ

Board index » User’s Questions & Discussions » Technical support




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: Draining/Refilling H220x please help!
 Post Posted: July 17th, 2017, 11:08 am 
Offline

Joined: July 17th, 2017, 11:00 am
Posts: 1
I have been using a H220x for some time now and it getting close to the min marker on the res. What is the best way to drain it so all of the water is removed? Also I noticed flakes in the fluid. How can I clean the inside of the pump and tubes the best that I can?


Top 
 Profile  
 
 Post subject: Re: Draining/Refilling H220x please help!
 Post Posted: July 20th, 2017, 6:48 pm 
Offline

Joined: May 12th, 2017, 7:14 pm
Posts: 28
duffit wrote:
I have been using a H220x for some time now and it getting close to the min marker on the res. What is the best way to drain it so all of the water is removed? Also I noticed flakes in the fluid. How can I clean the inside of the pump and tubes the best that I can?


The following youtube video by Gabriel Rouchon shows you how: https://www.youtube.com/watch?v=0fpum4J6C2k&list=PLsu8flm7MCjL8oAPpw0VFDz42qOnqFt7M&index=1&t=11s


Top 
 Profile  
 
 Post subject: Re: Draining/Refilling H220x please help!
 Post Posted: November 28th, 2017, 2:49 pm 
Offline
User avatar

Joined: August 29th, 2016, 8:40 am
Posts: 50
Instructions for draining liquid from AIO:
• You will need to remove the kit from the case.
• You will need to remove all coolant from the top fill port screw on top of the radiator.
• Then mix the 2 oz coolant with distilled water. It will have to = 503mL to fill up the kit and radiator.
• Check for leaks



CRITICAL: Unplug the power connector to the motherboard! Components (CPU, GPU, etc..) should not be running during the cleaning procedure.

Cleaning procedure

1. Mix (1) one to (2) two table-spoons of Pine-Sol® brand detergent to 1 Gallon of Distilled water; for a more vigorous cleaning you may use only 1/2 gallon if your system is very dirty or severely polluted with algae growth.

2. Cleaning: fill-up the loop, and run it with this mixture for several hours (no less than 3).

3. Rinsing: drain the mixture, then refill the loop with pure distilled water and run the system for no less that 30 min to rinse (you may run it longer if higher concentration of Pine-Sol was used).

4. Final rinse: drain the dirty rinse water, and refill the loop again with distilled water, and run the system again for no less than 20 minutes.

5. Completely drain the final rinse water; your system is now ready to be refilled with coolant.

Recommended Coolant: we recommend using a mix of 10% Hydrx + distilled water (1 bottle Hydrx to ½ Liter distilled water).

_________________
Kind Regards,
MAC
Technical Support / RMA Department


Top 
 Profile  
 
Display posts from previous:  Sort by  
 
Post new topic Reply to topic  [ 3 posts ] 

Board index » User’s Questions & Discussions » Technical support


Who is online

Users browsing this forum: No registered users and 1 guest

 
 

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron